CPSTest.io

Mouse Polling Rate Test

Move your mouse and see your real reporting rate, how steady it is, and whether any reports are being dropped.

Move the mouse in fast circles for the whole test.

10.0
Time left
–
Live rate (Hz)
–
Peak (Hz)
0
Reports

Click, then move the mouse

Keep moving in fast circles inside this box for 10 seconds. Pauses aren't counted.

Polling rate is a mouse measurement, so this test needs a mouse or trackpad rather than a touchscreen.

How to use the polling rate test

  1. Pick a test length

    5, 10 or 20 seconds. Longer runs give a steadier reading.

  2. Click the box to start

    The timer begins as soon as you click.

  3. Keep the mouse moving

    Move in fast circles inside the box. The box turns gold and asks you to move if you stop.

  4. Watch the live rate

    The big number is your current reporting rate, and the line behind it traces the last few seconds.

  5. Read your result

    You get your rate in Hz, how steady it was, your 1% low, and where every report landed.

What is a good polling rate?

For gaming, 1000 Hz is a good polling rate and the setting most players and professionals use. It sends a report every millisecond. Rates above that shave off fractions of a millisecond, but they cost CPU time and battery life, so they only make sense on strong hardware.

RateReport everyBest forTrade-off
125 Hz8 msOffice work, travel, saving batteryNoticeably less smooth for fast aiming
500 Hz2 msEveryday use and casual gamingA middle ground with almost no system cost
1000 Hz1 msAlmost everyone, including competitive playNone worth worrying about
2000 Hz0.5 msFast monitors, 240 Hz and aboveSmall extra CPU load
4000 Hz0.25 msHigh-end setups with a strong CPUMore CPU load, and much shorter wireless battery life
8000 Hz0.125 msEnthusiasts on top hardwareAround 1–3% extra CPU, which can cause stutter on weaker systems

Going from 125 Hz to 1000 Hz is a real, obvious change. Going from 1000 Hz to 8000 Hz saves 0.875 ms, which is far less than the delay added by your monitor and your own reaction time.

What your result means

ReadingWhat it tells you
The big numberYour rate from the middle of all the gaps between reports. It's the rate your mouse holds most of the time, matched to a standard rate when it's close enough.
AverageReports divided by the time you were actually moving. It sits slightly below the median if some reports arrive late.
PeakThe best rate over any quarter second, so it shows what your mouse can do at its best.
1% lowThe slowest 1% of reports, as a rate. If this sits far below your average, your mouse is dropping reports rather than holding a steady rate.
Steady reportsThe share of gaps close to your typical gap. Above 90% is healthy.
Where your reports landedEvery gap grouped by the rate it matches. One tall bar means a steady mouse; bars spread across several rates mean uneven reporting.

How to change your polling rate

Frequently asked questions

What is a mouse polling rate?

Polling rate is how many times per second your mouse tells your computer where it is, measured in hertz. At 1000 Hz it reports every millisecond. Between reports your computer doesn't know the mouse has moved, so a higher rate means fresher information.

Is 8000 Hz better than 1000 Hz?

Only slightly, and only on the right hardware. The report interval drops from 1 ms to 0.125 ms, a saving of 0.875 ms. That's worth having on a 240 Hz or faster monitor with a strong CPU, but on an average system the extra load can cost you more in stutter than you gain in speed.

Does polling rate affect CPU usage?

Yes. Every report interrupts the processor, so 8000 Hz creates eight times the interrupts of 1000 Hz. Razer puts the extra load at roughly 1–3% on modern hardware, which is nothing when idle but can matter in a game that's already pushing your processor.

Does a high polling rate drain a wireless mouse faster?

Yes, noticeably. The radio has to send far more often, and manufacturers' own figures show battery life cut by half or more at 4000 Hz and above. Many players use a high rate when plugged in and 1000 Hz or lower on battery.

Why does the test show a lower rate than my mouse setting?

Three common reasons. You may not be moving fast or continuously enough, since the test can only count reports while the mouse is actually moving. Your browser may be grouping mouse events, which caps what any web test can see. Or the mouse really isn't holding its rate, because of a USB hub, a power-saving setting, or wireless interference.

How accurate is a browser polling rate test?

It's accurate enough to confirm your rate and spot dropped reports, but it isn't a hardware measurement. Browsers and operating systems group mouse events before passing them on, so a web test shows the rate of events delivered to the page. Chrome and Edge pass through the most detail; some browsers cap the reading at your screen's refresh rate.

What is the difference between polling rate and DPI?

Polling rate is how often your mouse reports, measured in hertz. DPI is how far the cursor moves for each inch of hand movement, which is sensitivity. One is about timing, the other about distance, and changing one doesn't change the other.

Does polling rate matter on a 60 Hz or 144 Hz monitor?

Less than on a fast monitor, but 1000 Hz is still worth using. A 144 Hz screen draws a frame every 6.9 ms, so a 1000 Hz mouse already provides several reports per frame. At 360 Hz a frame appears every 2.78 ms, which is where higher rates start to show a measurable benefit.

Can I test a wireless or Bluetooth mouse?

Yes. Wired, 2.4 GHz wireless and Bluetooth mice all work. Bluetooth mice usually report at a much lower rate, often 125 Hz, so expect a lower number than a wired or 2.4 GHz gaming mouse.

My reading is uneven. What should I try?

Uneven reporting usually means something is interrupting the mouse rather than the mouse being faulty. Plug directly into the computer instead of a hub, try a different USB port, turn off USB power saving, charge a wireless mouse and move its receiver closer, and close heavy background apps before retesting.